急に機材が故障すると困る。
Express5800/GT110b まだ購入から2年も経っていない。
２世代前Core系1156な機材なのでよもや壊れると思わなかった。
原因はネコ。
ネコのやつがサーバの電源コンセントの付近に侵入し、稼働中の機材を
いきなり電源から止めてしまった。 無論、運用側の怠慢。キチンとした
電源タップを用意しておけば引っこ抜かれることはなかった。
まぁ、そんな事で壊れるようなことはめったにないと思っていた矢先、
ぶっ壊れてしまった事実は事実。 まあそんな事も有ろうかと予備機材として
同じ物を手元に持っていたからすぐに差し替えたけれども…
電源を入れるとBEEP音が次のパターンで鳴る。
"1-1-1-2"
こんなパターンは、PhenixBIOSのコードにもないようだ。
保証期間みたいなので取り敢えず日電さんに問い合わせすることにした。
はぁ。
取り敢えずBEEP音診断コードをサイトから取り寄せてみたので、載せておく。該当するものは無いのでこまった。
引用元： http://www.pchell.com/hardware/beepcodes.shtml#phoenix
Phoenix BIOS Beep Codes
| 1-1-3 |
Your computer can't read the
configuration info
stored in the CMOS. Replace the motherboard. |
| 1-1-4 |
Your BIOS needs to be replaced. |
| 1-2-1 |
You have a bad timer chip on the
motherboard.
You need a new motherboard. |
| 1-2-2 |
The motherboard is bad. |
| 1-2-3 |
The motherboard is bad. |
| 1-3-1 |
You'll need to replace the
motherboard. |
| 1-3-3 |
You'll need to replace the
motherboard. |
| 1-3-4 |
The motherboard is bad. |
| 1-4-1 |
The motherboard is bad. |
| 1-4-2 |
Some of your memory is bad. |
| 2-_-_ |
Any combo of beeps after two means
that some of
your memory is bad, and unless you want to get real technical, you
should probably have the guys in the lab coats test the memory for you.
Take it to the shop. |
| 3-1-_ |
One of the chips on your motherboard
is broken.
You'll likely need to get another board. |
| 3-2-4 |
One of the chips on your motherboard
that
checks the keyboard is broken. You'll likely need to get another
board. |
| 3-3-4 |
Your computer can't find the video
card. Is it
there? If so, try swapping it with another one and see if it
works. |
| 3-4-_ |
Your video card isn't working.
You'll need to
replace it. |
| 4-2-1 |
There's a bad chip on the
motherboard. You need
to buy another board. |
| 4-2-2 |
First check the keyboard for
problems. If
nothing, you have a bad motherboard. |
| 4-2-3 |
Same as 4-2-2. |
| 4-2-4 |
One of the cards is bad. Try yanking
out the
cards one by one to isolate the culprit. Replace the bad one. The last
possibility is to buy another motherboard. |
| 4-3-1 |
Replace the motherboard. |
| 4-3-2 |
See 4-3-1 |
| 4-3-3 |
See 4-3-1 |
| 4-3-4 |
Time of day clock failure. Try
running the
setup program that comes with the computer. Check the date and time. If
that doesn't work, replace the battery. If that doesn't work, replace
the power supply. You may have to replace the motherboard, but that is
rare. |
| 4-4-1 |
Your serial ports are acting up.
Reseat, or
replace, the I/O card. If the I/O is on the motherboard itself, disable
them with a jumper (consult your manual to know which one) and then add
an I/O card. |
| 4-4-2 |
See 4-4-1, but this time is your
Parallel port
that's acting up. |
| 4-4-3 |
You math coprocessor is having
problems. Run a
test program to double-check it. If it is indeed bad, disable it, or
replace it. |
| Low 1-1-2 |
Your motherboard is having problems |
| Low 1-1-3 |
This is an Extended CMOS RAM
problem, check
your motherboard battery, and motherboard. |
引用元：
http://www.bioscentral.com/beepcodes/phoenixbeep.htm
こっちのほうが最近の４分割パターンである。
Beeps
|
Description
|
| 1-1-1-3 |
Verify real mode |
| 1-1-2-1 |
Get CPU type |
| 1-1-2-3 |
Initialize system hardware |
| 1-1-3-1 |
Initialize chipset
registers with initial values |
| 1-1-3-2 |
Set in POST flag |
| 1-1-3-3 |
Initialize CPU registers |
| 1-1-4-1 |
Initialize cache to
initial values |
| 1-1-4-3 |
Initialize I/O |
| 1-2-1-1 |
Initialize power management |
| 1-2-1-2 |
Load alternative registers
with initial POST values |
| 1-2-1-3 |
Jump to UserPatch0 |
| 1-2-2-1 |
Initialize timer initialization |
| 1-2-3-1 |
8254 timer initialization |
| 1-2-3-3 |
8237 DMA controller
initialization |
| 1-2-4-1 |
Reset Programmable
Interrupt Controller |
| 1-3-1-1 |
Test DRAM refresh |
| 1-3-1-3 |
Test 8742 Keyboard
Controller |
| 1-3-2-1 |
Set ES segment register
to 4GB |
| 1-3-3-1 |
Autosize DRAM |
| 1-3-3-3 |
Clear 512K base memory |
| 1-3-4-1 |
Test 512K base address
lines |
| 1-3-4-3 |
Test 51K base memory |
| 1-4-1-3 |
Test CPU bus-clock
frequency |
| 1-4-2-1 |
CMOS RAM read/write
failure (this commonly indicates a problem on the ISA bus such
as a card not seated) |
| 1-4-2-4 |
Reinitialize the chipset |
| 1-4-3-1 |
Shadow system BIOS
ROM |
| 1-4-3-2 |
Reinitialize the cache |
| 1-4-3-3 |
Autosize the cache |
| 1-4-4-1 |
Configure advanced
chipset registers |
| 1-4-4-2 |
Load alternate registers
with CMOS values |
| 2-1-1-1 |
Set initial CPU speed |
| 2-1-1-3 |
Initialize interrupt
vectors |
| 2-1-2-1 |
Initialize BIOS interrupts |
| 2-1-2-3 |
Check ROM copyright
notice |
| 2-1-2-4 |
Initialize manager
for PCI Options ROMs |
| 2-1-3-1 |
Check video configuration
against CMOS |
| 2-1-3-2 |
Initialize PCI bus
and devices |
| 2-1-3-3 |
initialize all video
adapters in system |
| 2-1-4-1 |
Shadow video BIOS ROM |
| 2-1-4-3 |
Display copyright notice |
| 2-2-1-1 |
Display CPU type and
speed |
| 2-2-1-3 |
Test keyboard |
| 2-2-2-1 |
Set key click if enabled |
| 2-2-2-3 |
Enable keyboard |
| 2-2-3-1 |
Test for unexpected
interrupts |
| 2-2-3-3 |
Display prompt "Press
F2 to enter setup" |
| 2-2-4-1 |
Test RAM between 512K
and 640K |
| 2-3-1-1 |
Test expanded memory |
| 2-3-1-3 |
Test extended memory
address lines |
| 2-3-2-1 |
Jump to UserPatch1 |
| 2-3-2-3 |
Enable external and
CPU caches |
| 2-3-2-3 |
Configure advanced
cache registers |
| 2-3-3-1 |
Enable external and
CPU caches |
| 2-3-3-2 |
Initialize SMI handler |
| 2-3-3-3 |
Display external cache
size |
| 2-3-4-1 |
Display shadow message |
| 2-3-4-3 |
Display non-disposable
segments |
| 2-4-1-1 |
Display error messages |
| 2-4-1-3 |
Check for configuration
errors |
| 2-4-2-1 |
Test real-time clock |
| 2-4-2-3 |
Check for keyboard
errors |
| 2-4-4-1 |
Setup hardware interrupt
vectors |
| 2-4-4-3 |
Test coprocessor if
present |
| 3-1-1-1 |
Disable onboard I/O
ports |
| 3-1-1-3 |
Detect and install
external RS232 ports |
| 3-1-2-1 |
Detect and install
external parallel ports |
| 3-1-2-3 |
Reinitialize onboard
I/O ports |
| 3-1-3-1 |
Initialize BIOS Data
Area |
| 3-1-3-3 |
Initialize Extended
BIOS Data Area |
| 3-1-4-1 |
Initialize floppy controller |
| 3-2-1-1 |
Initialize hard disk
controller |
| 3-2-1-2 |
Initialize local bus
hard disk controller |
| 3-2-1-3 |
Jump to UserPatch2 |
| 3-2-2-1 |
Disable A20 address
line |
| 3-2-2-3 |
Clear huge ES segment
register |
| 3-2-3-1 |
Search for option ROMs |
| 3-2-3-3 |
Shadow option ROMs |
| 3-2-4-1 |
Setup power management |
| 3-2-4-3 |
Enable hardware interrupts |
| 3-3-1-1 |
Set time of day |
| 3-3-1-3 |
Check key lock |
| 3-3-3-1 |
Erase F2 prompt |
| 3-3-3-3 |
Scan for F2 keystroke |
| 3-3-4-1 |
Enter SETUP |
| 3-3-4-3 |
Clear in-POST flag |
| 3-4-1-1 |
Check for errors |
| 3-4-1-3 |
POST done - prepare
to boot operating system |
| 3-4-2-1 |
One beep |
| 3-4-2-3 |
Check password (optional) |
| 3-4-3-1 |
Clear global descriptor
table |
| 3-4-4-1 |
Clear parity checkers |
| 3-4-4-3 |
Check virus and backup
reminders |
| 4-1-1-1 |
Try to boot with INT
19 |
| 4-2-1-1 |
Interrupt handler error |
| 4-2-1-3 |
Unknown interrupt error |
| 4-2-2-1 |
Pending interrupt error |
| 4-2-2-3 |
Initialize option ROM
error |
| 4-2-3-1 |
Shutdown error |
| 4-2-3-3 |
Extended Block Move |
| 4-2-4-1 |
Shutdown 10 error |
| 4-2-4-3 |
Keyboard Controller
failure (most likely problem is with RAM or cache unless no video
is present) |
| 4-3-1-3 |
Initialize the chipset |
| 4-3-1-4 |
Initialize refresh
counter |
| 4-3-2-1 |
Check for Forced Flash |
| 4-3-2-2 |
BIOS ROM is OK |
| 4-3-2-4 |
Do a complete RAM test |
| 4-3-3-1 |
Do OEM initialization |
| 4-3-3-2 |
Initialize interrupt
controller |
| 4-3-3-3 |
Read in bootstrap code |
| 4-3-3-4 |
Initialize all vectors |
| 4-3-4-2 |
Initialize the boot
device |
| 4-3-4-3 |
Boot code was read
OK |
